479885
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
INSTALLER MANUAL - PAGE 05PAGE 04 - INSTALLER MANUAL
INSTALLER MANUAL
BLACK
RED
6-way connector to plug into
the free connector
on the BSI control unit
marked
“EA”
5.0 - COMPLETE ELECTRIC DIAGRAM
CAN BUS signal
LIGHT BLUE (CAN-L)
LIGHT BLUE-GREY (CAN-H)
3
1
6
4
6.0-U
6.1 - CONNECTIONS AND POSITIONING
6.2 - SENSOR ADJUSTMENT
Insert the WHITE connector
.
:
.
LTRASONIC VOLUMETRIC PROTECTION
in the the “W” socket on the control unit.
Insert the RED connector in the “R” socket on the control unit.
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the aeration inlets and orient them towards the center of the rear window
o check sensors proceed as follows
With system disarmed, roll down the front window approx. 20 cm.
Set the trimmer on the control unit to the middle position.
Close doors, bonnet and boot and arm the system.
During the system inhibit arming time, introduce an object in the cabin and move it around; the
status LED will turn off to signal a presence.
If sensibility level is too low, adjust trimmer again and repeat above procedure
!
!
!
!
!
ULTRASONIC
CELLS
CONNECTIONS
SENSIBILITY
ADJUSTMENT
4.0 - CONNECTORS TABLES
Ground
-----
Positive
-----
-----
-----
-----
-----
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-9-
-10-
-11-
-12-
-13-
-14-
-15-
-16-
-17-
-18-
-19-
-20-
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-----
-----
-----
-----
-----
-----
BROWN
BLACK
RED
-----
LIGHT BLUE-GREY
LIGHT BLUE
PINK
GREEN-BLACK
-----
-----
-----
-----
-----
----
BLACK
-----
RED
-----
-----
-----
-----
-----
WIRE FUNCTION
WIRE FUNCTION
POSITION
POSITION
WIRE COLOUR
WIRE COLOUR
4.1 - 20-WAY CONNECTOR
4.2 - 8-WAY CONNECTOR
-----
-----
-----
-----
-----
-----
Grund for external sensor connector
LED negative output
LED positive output
-----
CAN BUS signal (CAN-H)
CAN BUS signal (CAN-L)
Positive output with system armed (+A)
External sensor negative input
-----
-----
-----
-----
-----
-----
For the system to work properly, the “original alarm installed” feature (BSI unit)
must first be enabled via the specific diagnostic tester available at any authorized
Peugeot-Citroën dealer (PSA group).
Moreover, this type of system DOES NOT require that you program the vehicle
code, it is already factory-registered by Gemini.
NEVER PRESS THE PROGRAMMING BUTTON LOCATED NEXT TO THE UNIT
BUILT-IN LED
!
Before carrying out all
electrical connections,
disconnect the
negative battery
terminal and re-
connect again after
completion.
!
Red
Black
Connector for external modules
Pink
Brown
Green-Black
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 931PSA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 931PSA in de taal/talen: Engels als bijlage per email.

De handleiding is 0,18 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info