479879
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
10.0 - SSELF-LEARNING OF TURN INDICATORS FLASHE
In order to arm/disarm through the turn indicators, the system must learn the vehicle
locking(arming)/unlocking (disarming) signals.
To do so, connect the WHITE-ORANGE wire to the turn indicators and then proceed as follows:
Disconnect the 8-way wiring connector from the 8-way system connector.
Turn ignition key “ON”.
Connect the 8-way wiring connector to the 8-way system connector; the LED will turn on.
urn ignition key
Close any open door and press the lock button on the original remote control.
Once the turn indicators stop flashing, the system will emit 1 high-pitched audio signal indicating
the arming flashes have been memorized.
Press the unlock button on the original remote control.
Once the turn indicators stop flashing, the system will emit 2 high-pitched audio signals indicating
the disarming flashes have been memorized.
This completes the procedure.
!
!
!
!
!
!
!
!
! T “OFF”.
12.0 - SYSTEM PROGRAMMING
The t
E
able below applies to the system programmed in “standard configuration”.
ntering the programming procedure resets the functions to the default setting.
Visual signals activated by a connection to the hazard button, will ONLY turn on during
an alarm situation.
The system BLU wire MUST be connected to the hazard button.
The system ORANGE wires MUST NOT be connected to the turn indicators (see
chapter 8.3).
!
Alack of power during electrical system maintenance, will not affect the programming.
The procedure must be carried out completely because functions are disabled by changing the
position of the ignition key, which then activates the next step up to completion of the programming
procedure.
The next paragraph illustrates the programming instructions.
Programmable functions are briefly described below.
This function activates visual signals during system arming (1) and disarming (2).
12.1 - OPTICAL SIGNALLING
The turn indicators alarm signals should be disactivated if visual signals are present
when locking/unlocking the vehicle.
12.2 - ACOUSCTIC SIGNALLING
12.3 - PASSIVE ARMING
12.4 - 5)
12.5 - BOOT PUSH-BUTTON POLARITY SELECTION
12.6 - IMPULSE VISUAL SIGNALLING SELECTION
This function activates audio signals during system arming (1) and disarming (2).
(art. 7725).
This function modifies the alarm input signal (positive or negative) according to the signal
This function activates the
This function arms the system 60” after switching off ignition and opening and closing the last door.
Opening a door during this operation interrupts the procedure which will resume when door is closed.
sent by the
boot push-button.
visual signalling according to the connection; it must be activated only
when connections are made directly on the wire deriving from the hazard button (not availablbe for all
vehicles).
ARMING OF SIREN (ART. 772 OUTPUT
This function arms the relative output (20-way connector, position 13, PINK wire) to activate the self-
powered coded siren
!
FUNCTION STATUS
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Exclusion of arming/disarmin optic signalling
Exclusion of arming/disarmin acoustic signalling
System passive arming
Arming of self-powered coded siren
Positive signal trunk input
Impulse visual signalling
Negative output during alarm phase
INSTALLER MANUAL - PAGE 11PAGE 10 - INSTALLER MANUAL
To cancel the programming of the turn indicators reset the system (see
chapter 15.0).
!
11.0 - DIP-SWITCHES PROGRAMMING TABLE
Set dip-switches BEFORE connecting the alarm system.
If settings must be modified after installation, FIRST disconnect alarm and then reset
dip-switches.
With dip-switch nr. 2 “ON”, YELLOW-RED wire is grounded when system is armed.
With the vehicle closed, leave dip-switch in this position when connecting only the
WHITE/LIGHT BLUE wire to the lock switch (connected to ground).
!
!
Nr. POSITION FUNCTION
ON
OFF
ON
OFF
ON
OFF
ON
OFF
POSITIVE polarity for control on WHITE/LIGHT BLUE wire
NEGATIVE polarity for control on WHITE/LIGHT BLUE wire
Positive signal (+A) on BROWN/RED with alarm on
Normal functionning
Negative commands - arming/disarming system
Positive commands - arming/disarming system
System arming with door locking motor unit or with door locking motor unit
and turn indicators (see par. 9.0)
System arming with turn indicators only
1
1
2
2
3
3
4
4
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 822 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 822 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Gemini 822

Gemini 822 Gebruiksaanwijzing - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info