479863
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
PAGE 6
PAGE 7
PROGRAMMING THE ALARM SYSTEM
Has been previously programmed with standard configuration during
manufacturing procedure by Gemini, and can be modified in any moment
With alarm being disarmed, open and keep it open the driver side door.
Turn the ignition "ON".
he status led stay on for 0,5 seconds; during this time, push both the two
buttons of the remote control at the same time.
Starting of programming procedure is indicated by two flashes of the
vehicle indicators.
To activate and de-activate the functions, follow the below table, taking
into consideration that every time the transmitter button is pressed, the
system moves to the next function.
!
!
!
!
!
During the programming phases, press the radio control (rough) push-button
n.1, for function activation and the (smooth) push-button n.2, for function de-
activation.
For the programming modification proceed as follows:
Coninuous or intermittent
siren sound
Double pulse when opening
Panic or boot opening
function
Setting of centralized lock
times (0,5 - 6 sec)
25 seconds comfort closure
command
Power drain must remain
disabled
Anti-distraction, automatic
door locking function
Continuous
Disabled
Disabled
0,5” selected
Disabled
Disabled
Panic function
enabled
Button N°1- Intermittent
N°2-
N°1-
N°2- Enable
N°1-
N°2-
---------
N°2-
Button Continuous
Button Enable 6”
Button 0,5”
Button Enable
Button Disable
Button N°1- Enable
Button N°2- Disable
Button Disable
Button N°1- Enable panic
Button N°2- Enable car-finder
Button N°1- Enable
Button N°2- Disable
FUNCTION STATE BUTTON
NOTE:
Once the last function has been programmed, the alarm will flash the
vehicles indicators and the LED twice confirming the exit of the
programming procedure.
Turn the ignition “OFF”.
!
!
by turning the ignition key to OFF”, the alarm will exit the programming
procedure with all the changes stored.
LEARNING OF NEW CONTROL DEVICES
ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
ATTENTION:
The alarm can save to memory a maximum number of 12 control devices,
either radio controlled, or electronic keys, TAG cards or magnetic contact (the
later as a protection device).
Proceed as follows:
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
Turn the ignition “ON”.
The alarm will indicate the procedure starting by two slow flashes of the
turn signal; now the alarm is waiting for receiving the device code.
Press the radio control push-button 1, introduce the electronic key in the
specific receptacle, press the TAG card button, make the magnetic contact
to transmit (bring near and then take away contact and magnet) or make the
infrared sensor to transmit (see sensor instructions), according to the
device to be saved to memory.
In all four cases, the alarm will indicate the new device learning, by one led
flashing.
Repeat the procedure to save to memory other devices.
Turn the ignition “OFF”.
The procedure completion will be indicated by one flash of the turn signal.
!
!
!
!
!
!
!
!
!
passive alarm activation must be disabled.
Press a previously learned remote control push-button or insert an already
coded electronic key in the specific receptacle.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 7590T2-1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 7590T2-1 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info