479862
7
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
PAG . 12
PAG . 13
LEARNING OF NEW CONTROL DEVICES
ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
ATTENTION: the following operations must be carried out within four
seconds, otherwise the new device memorizing procedure will be
invalidated.
ATTENTION: do not modify the bonnet position, otherwise instead of
saving to memory new devices, deletion of existing ones in the alarm´s
memory will take place.
The alarm can save to memory a maximum number of 12 control devices,
either radio controlled, or electronic keys, TAG cards or magnetic contact (the
later as a protection device).
Proceed as follows:
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
Turn the ignition key to “ON”.
Turn the ignition key to “OFF”.
Re-turn the ignition key to “ON” for three consecutive times (ignition key to
“ON” and “OFF”), within the maximum time of four seconds, as mentioned
before.
After the third commutation, let the ignition key to “ON”.
The alarm will indicate the procedure starting of new control device or
magnetic contact learning, by two long turn signal flashes and two acoustic
signals, one acute tone and the other loud tone.
Now the alarm is waiting for receiving the device code.
Press the radio control push-button 1, introduce the electronic key in the
specific receptacle, press the TAG card button or make the magnetic
contact to transmit (bring near and then take away contact and magnet),
according to the device to be saved to memory.
In all four cases, the alarm will indicate the new device learning, by one turn
signal flashing and one acute tone signal.
Repeat the procedure to save to memory other devices.
Turn the ignition key to “OFF”.
The procedure completion will be indicated by one long turn signal flashing
and one loud tone signal.
!
!
!
!
!
!
!
!
!
DELETION OF PROGRAMMED CONTROL DEVICES
ATTENTION: in order to carry out successfully the operation, it is
necessary to make the required electrical connections (door switch,
bonnet switch and positive under key).
ATTENTION: the following operations must be carried out within four
seconds, otherwise the new device deletion procedure will be
invalidated.
NOTE: keeping the bonnet close for less than four seconds, the device
deletion via radio will be unsuccessful.
NOTE: the control device deletion does not imply any modification of
The alarm is equipped with a deletion procedure of new control devices, either
radio controlled, or electronic keys, TAG cards or magnetic contact (the later as
a protection device).
Proceed as follows:
With the alarm being disarmed, open and keep open the bonnet and the
driver side door.
Turn the ignition key to “ON”.
Turn the ignition key to “OFF”.
Re-turn the ignition key to “ON” for three consecutive times (ignition key to
“ON” and “OFF”), within the maximum time of four seconds, as mentioned
before.
After the third commutation, let the ignition key to “ON”.
The alarm will indicate the procedure starting of new control device or
magnetic or magnetic contact deletion, by two long turn signal flashes and
two acoustic signals, one acute tone and the other loud tone.
Close the bonnet.
The led will be illuminated constantly.
Keep the bonnet close till the moment, the complete deletion of devices
via radio, will take place (after about four seconds).
The procedure completion will be indicated by led´s turning off, by one
long turn signal flashing and one loud tone signal.
Turn the ignition key to “OFF”.
!
!
!
!
!
!
!
!
!
!
Nominal tension
Nominal supply voltage range
Current absorption @ 12Vdc
Turn signal contact rating
Engine block contact rating
Alarm triggering
Max positive current with system armed (+A)
Sirene output current capacity
12 Vdc
< 2mA with systme armed
and led
10A a 20°C
30 sec.
9 15Vdc¸
flashing
8A a 20°C
700 mA
3A
TECHNICAL DATA
7

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Gemini-7590T

Zoeken resetten

  • Goedemiddag ,kunt uw mij helpen ,ik heb een probleem met mijn gemini alarm 7590tn. bij het testen merkte ik dat het alarm niet afging bij het openen van de motorkap, verder werkte alles perfect Wanneer ik de draad aanraakte die van de schakelaar van het motorkap alarm naar de sirene gaat ging het alarm wel af .Dacht toen dat het misschien een draadbreuk of een slecht contact zou kunnen zijn. Heb daarom het stekkertje van de motorkapschakelaar losgemaakt en schoongemaakt, verder heb ik de stekker van de sirene losgemaakt ,schoongemaakt en met contactspray ingespoten. Toen alles weer aangesloten maar helaas werkt het alarm nu niet meer. Heb geprobeerd het aan te zetten met beide sleutels maar er gebeurt niets .Alleen lampje in de sleutels brand groen . toch nog nieuwe batterijen in de sleutels geprobeerd maar nog steeds niets. ook met de elektronische sleutel op het dashboard geprobeerd maar nog steeds alarm.
    centrale deurvergrendeling werkt wel naar behoren .kunt uw mij vertellen wat ik verkeerd gedaan heb of heb ik misschien iets over het hoofd gezien. Zou uw zeer dankbaar zijn voor deskundig advies.
    met vriendelijke groet ,
    Bert van Osta Gesteld op 28-5-2022 om 16:54

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 7590T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 7590T in de taal/talen: Engels als bijlage per email.

De handleiding is 0,13 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info