691896
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
4
Select Done.
Performing Basic Calibration
If you connect the sensor to a NMEA 2000 network without a
compatible Garmin chartplotter, you must perform basic
calibration instead of menu-based calibration.
You must be able to view heading data from the sensor on a
connected chartplotter or marine display before you can perform
basic calibration. If you cannot view heading data on your
connected display, check the NMEA 2000 network and power
connections.
All other sources of heading data that are not based on GPS
must be removed from the NMEA 2000 network while
performing basic calibration.
When performing basic calibration, you first calibrate the
compass and then align the heading in one continuous
procedure. If you installed the sensor with the cable pointing
toward the bow, parallel to the keel, it may not be necessary to
align the heading.
NOTE: If you choose to align the heading, you must connect a
GPS source to the NMEA 2000 network. The boat must be able
to reach a cruising speed of at least 6.4 km/h (4 mph) to perform
the heading alignment.
1
Drive the boat to a location with calm, open water.
2
Set the display to view heading data from the connected
sensor.
3
Disconnect the sensor from the NMEA 2000 network or turn
off the power to the NMEA 2000 network.
4
Wait while the boat becomes level and stationary.
5
Turn on power to the sensor, and wait until the heading data
appears on the display
À
.
6
Within three minutes, complete two full, slow, tight circles
Á
,
taking care to keep the boat as steady and level as possible.
The boat should not list during calibration.
If possible, you can turn the vessel in place by engaging two
engines in opposite directions.
When the sensor is prepared to calibrate the compass, the
heading data disappears from the display
Â
You may receive an error message that the heading was lost.
You can ignore this message.
7
Continue turning in the same direction at the same speed
Ã
for approximately 1
1
/
2
rotations until the heading data
appears
Ä
.
When the heading data appears, the compass has been
calibrated successfully, and you can align the heading
(optional).
8
Select an option.
If you want to align the heading to match the front of the
boat, proceed to the next step.
If you installed the sensor with the arrow pointing parallel
to the front of the boat, and do not want to align the
heading, stop turning and wait, keeping the boat
stationary. Over the next two minutes the heading data
should disappear and then reappear. When the heading
data reappears, the compass should be calibrated and no
heading offset should be applied.
NOTE: If an unwanted heading offset is applied, you must
disconnect all GPS sources from the NMEA 2000 network,
and repeat the calibration. If the only available heading
display is also a GPS source, you must repeat the
calibration, and disconnect the sensor after step 7.
9
Continue turning in the same direction at the same speed for
approximately ten seconds, until the heading data disappears
from the display
Å
.
10
When it is safe, straighten the boat and drive in a straight line
Æ
at cruising speed (must be at least 6.4 km/h (4 mph)) until
the heading data appears
Ç
.
When the heading appears, the compass has been
calibrated, and the heading has been aligned on the sensor.
11
Test the results of the calibration, and repeat this procedure if
necessary.
Restoring Factory Default Settings
If you relocate the sensor or do not believe the calibration was
successful, you can delete all calibration information from the
sensor, and restore its factory default settings. After restoring
the factory default settings, you must configure the sensor
before you can use it with your system.
1
Select Settings > Communications > NMEA 2000 Devices
> Device List.
2
Select the name of the sensor.
3
Select Review > Factory Defaults > Yes.
Specifications
Specification Measurement
Dimensions (L x W x H) 87.35 x 53.84 x 34.29 mm (3.4 x 2.1 x
1.4 in.)
Weight 182 g (6.4 oz.)
Temperature range From -15° to 70°C (from 5° to 158°F)
Material Fully gasketed, high-impact plastic
Water resistance IEC 60529 IPX7*
NMEA 2000 input voltage From 9 to 32 Vdc
NMEA 2000 LEN 2 (100 mA)
Compass-safe distance 5 cm (2 in.)
3
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin SteadyCast bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin SteadyCast in de taal/talen: Engels als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin SteadyCast

Garmin SteadyCast Installatiehandleiding - Nederlands - 4 pagina's

Garmin SteadyCast Installatiehandleiding - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info