466630
2
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Operation Guide 2894
2
3. Press D to move the flashing in the sequence shown below to select the
other settings.
The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use C and/
or A to change it as described below.
Year
Seconds
Hour
Minutes
Day
Month
12/24-Hour
Format
Power
Saving
Barometric
Pressure Unit
Altitude Unit
Temperature
Unit
City Code
DST
Do this:
Use C (east) and
A(west).
Press C
.
Press C.
To do this:
Change the city code
Toggle between Daylight Saving
Time (
ON) and Standard Time
(
OFF).
Toggle between 12-hour (
12H
)
and 24-hour (
24H
) timekeeping.
Screen
Press C
.
Use C(+) and A().
Reset the seconds to
00
Change the hour or minutes
Change the year
Change the month or day
5. Press E to exit the setting screen.
Note
See Daylight Saving Time (DST) for details about the DST setting.
You also need to enter the Timekeeping Mode in order to configure the
following settings.
Display illumination duration (To specify the illumination duration)
Power saving on/off (To turn Power Saving on and off)
Temperature, barometric pressure, and altitude units (To select the
temperature, barometric pressure, and altitude units)
The year can be set in the range of 2000 to 2099. The day of the week is
calculated automatically in accordance with the date you set.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour
from Standard Time. Remember that not all countries or even local areas use
Daylight Saving Time.
To toggle the Timekeeping Mode digital time between DST and
Standard Time
1. In the Timekeeping Mode, hold down E until
the city code starts to flash, which indicates
the setting screen.
2. Press D once and the DST setting screen
appears.
3. Press C to toggle between Daylight Saving
Time (
ON
displayed) and Standard Time
(
OFF
displayed).
4. Press E to exit the setting screen.
The DST indicator appears on the display to
indicate that Daylight Saving Time is turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Digital Compass
A built-in bearing sensor detects magnetic north and indicates one of 16
directions on the display. Direction readings are performed in the Digital
Compass Mode.
You can calibrate the bearing sensor if you suspect the direction reading is
incorrect.
To enter and exit the Digital Compass Mode
1. While in the Timekeeping or in any of the other
sensor modes, press A to enter the Digital
Compass Mode.
At this time, the watch will start a Digital
Compass operation. After about two
seconds, letters appear on the display to
indicate the direction that the 12 oclock
position of the watch is pointing.
l
l
l
l
l
l
l
l
l
l
l
l
Timekeeping Mode time
12 oclock position
The direction reading on the display is updated each second for up to 20
seconds, after which measurement stops automatically.
The ACT indicator flashes on the display while a measurement is in
progress.
2. Press D to return to the Timekeeping Mode.
To take a direction reading
1. While the watch is in the Digital Compass
Mode, place it on a flat surface or, if you are
wearing the watch, make sure that your wrist
is horizontal (in relation to the horizon).
2. Point the 12 oclock position of the watch in
the direction you want to measure.
3. Press A to start a Digital Compass
measurement operation.
After about two seconds, the direction that the
12 oclock position of the watch is pointing
appears on the display.
Also, four pointers appear to indicate magnetic
north, south, east, and west.
After the first reading is obtained, the watch
continues to take direction readings
automatically each second, for up to 20
seconds.
Direction
indicator
Angle value (in degrees)
Magnetic north pointer
12 oclock position
NW
0°
W
N
W
W
W
S
W
SW
S
S
W
S
SS
E
SE
E
S
E
E
ENE
NE
N
N
E
N
NNW
90°
180°
270°
During measurement, the watch displays an angle value, a direction
indicator, and four direction pointers, which change dynamically when the
watch is moved. After measurement is complete, the angle value,
direction indicator, and four direction pointers are frozen in accordance
with the last measurement.
The ACT indicator flashes on the display while a measurement is in
progress.
Note
Note that taking a measurement
while the watch is not horizontal
(in relation to the horizon) can
result in large measurement error.
The margin of error for the angle value is ±11 degrees. If the indicated
direction is northwest (NW) and 315 degrees, for example, the actual
direction can be anywhere from 304 to 326 degrees.
Any ongoing direction measurement operation is temporarily paused while
the watch is performing an alert operation (daily alarm, Hourly Time Signal,
countdown timer alarm) or while illumination is turned on (by pressing L).
The measurement operation resumes for its remaining duration after the
operation that caused it to pause is finished.
The following table shows the meanings of each of the direction
abbreviations that appear on the display.
See Digital Compass Precautions for other important imformation about
taking direction readings.
Direction
Meaning
Direction
Meaning
Direction
Meaning
Direction
Meaning
NNE
ESE
SSW
WNW
NE
SE
SW
NW
North-
northeast
East-
southeast
South-
southwest
West-
northwest
Northeast
Southeast
Southwest
Northwest
East-
northeast
South-
southeast
West-
southwest
North-
northwest
ENE
SSE
WSW
NNW
North
East
South
West
N
E
S
W
Barometer/Thermometer
This watch uses a pressure sensor to measure air pressure (barometric
pressure) and a temperature sensor to measure temperature.
You can calibrate the temperature sensor and the pressure sensor if you
suspect that readings are incorrect.
To take barometric pressure and temperature readings
Pressing B in the Timekeeping or in any of other
sensor modes enters the Barometer/
Thermometer Mode and automatically starts
barometric pressure and temperature
measurements.
It can take up to four or five seconds for the
barometric pressure reading to appear after
you enter the Barometer/Thermometer Mode.
Barometric pressure is displayed in units of
1hPa (or 0.05 inHg).
Temperature
Barometric
pressure
Barometric
pressure graph
Pressure
differential
pointer
The displayed barometric pressure value changes to
xxxx
hPa (or inHg) if
a measured barometric pressure falls outside the range of 260 hPa to
1100 hPa (7.65 inHg to 32.45 inHg). The barometric pressure value will
reappear as soon as the measured barometric pressure is within the
allowable range.
Temperature is displayed in units of 0.1°C (or 0.2°F).
The displayed temperature value changes to
xxx
°C (or °F) if a measured
temperature falls outside the range of 10.0°C to 60.0°C (14.0°F to
140.0°F). The temperature value will reappear as soon as the measured
temperature is within the allowable range.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 2894 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 2894 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Casio 2894

Casio 2894 Gebruiksaanwijzing - Nederlands - 13 pagina's

Casio 2894 Gebruiksaanwijzing - Deutsch - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info