577997
5
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
5
ENGLISH
4. Protractor
5. Set square
6. Front foot
Assembly
Warning! Make sure that the tool is switched off.
Fitting the batteries (fig. A)
Remove the battery cover (3) from the tool.
Insert the batteries into the tool in the orientation as shown.
Refit the cover and let it click into place.
Installing the tool (fig. B & C)
The tool can be installed on the protractor provided.
Alternatively, the tool can be installed with the protractor on
the set square provided.
Fitting the tool to the protractor
Before installing the tool onto the protractor, the front foot (6)
must be retracted.
Position the protractor on the workpiece.
Align the bottom of the tool with the protractor (4).
At intermediate angles, place the rear feet (7) into the
circular groove (8).
At fixed/pre-set angles, place the rear feet into the
corresponding holes (9).
Installing the protractor (fig. C & D)
The tool can be used with the protractor to project laser lines
at a fixed/pre-set or intermediate angle, at any position on or
from the edge of a workpiece. For improved accuracy, a set
square (5) is provided with the tool.
Against the workpiece (fig. C)
Flip up the edge locators (10).
Align the edge locators with the edge of the workpiece.
Position the protractor (4) on the workpiece. Make sure
the edge locators fit snug against the workpiece.
Place the tool onto the protractor.
Using the set square (fig. D)
Align the set square (5) with the edge of the workpiece.
Position the set square on the workpiece.
Cling the protractor (4) on the set square. Make sure the
raised edge (11) fits snug against the set square.
Place the tool onto the protractor.
Use
Fold out the front foot (6).
If necessary, install the tool onto the protractor (4) and/or
set square (5).
Slide the on/off switch (1) forward to switch the tool on.
Move the tool as necessary to position the laser line. The
laser beam marks the intended line of cut.
After finishing work, always switch off the tool by sliding
the on/off switch (1) backward.
Use with the protractor (fig. B)
Fixed/preset angles (fig. E)
Align the feet (7) of the tool with a combination of holes
on the protractor (4). Refer to the table below for a list of
fixed angles that can be selected.
Fit the feet into the holes.
Switch on the tool.
Angle
12. 0° left parallel with the edge of the workpiece.
13. 30° left
14. 45° left
15. 90° at a square angle with edge of workpiece.
16. 45° right
17. 30° right
18. 0° right parallel with the edge of the workpiece.
Intermediate angles (fig. B)
Align the feet (7) of the tool with the circular groove (8) in
the protractor (4).
Fit the feet into the circular groove.
Adjust the position of the tool as necessary to position
the laser line.
Switch on the tool.
Use with the set square (fig. D)
Position the set square as required on the workpiece.
Mark the starting point for the intended cut using the set
square ruler.
Place the protractor (4) onto the set square. Align the 90°
indication (19) with the mark on the workpiece.
Place the tool onto the protractor.
Switch on the tool.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Black Decker BDL100P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Black Decker BDL100P in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,47 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Black Decker BDL100P

Black Decker BDL100P Gebruiksaanwijzing - Polski - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info