5019 412 10101
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration*
(hours : minutes)
White Cotton 95 5.5 55** 1.70 1:55
Cotton*** 60 5.5 49 1.02 2:25
Cotton 40 5.5 53 0.55 2:00
Synthetics 60 2.5 53** 0.85 1:30
Synthetics 40 2.5 47 0.50 1:15
Daily load 40 3.0 43 0.48 1:00
Quick wash 30 3.0 36 0.30 0:30
Delicate 40 1.5 51 0.50 0:45
Wool 40 1.0 53 0.50 0:45
Handwash 40 1.0 43 0.50 0:35
Handwash 30 1.0 42 0.30 0:31
CONSUMPTION DATA
Bauknecht is a registered trademark.
Add detergent as indicated an the front page and as
described in the chapter “Detergent and Additives” in
your Instructions for Use.
1. Turn the programme selector to the desired
programme.
2. The temperature and spin speed indicated on the
display can be altered by pressing the “Temperature”
button or the “Variable spin” button. The light next
to the “Start/Pause” button flashes.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the
home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type
of wash.
* The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE LID AND
SELECT THE PROGRAMME
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
RED INDICATIONS ON THE DISPLAY
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in the
latter case refer to the Instructions for Use (“Removing
the Filter”).
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”;
if the fault persists, contact our After Sales Service.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and
“Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
• If you select “Rinse Hold”, do not leave items to
soak for too long.
Note: The programme stops to “Rinse hold” at the
time the “Rinse hold” symbol on the display lights up.
The blue light under the “Start/Pause” button
flashes.
Terminate the “Rinse Hold” option:
• Press the “Start/Pause” button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to “Drain” and press the
“Start/Pause” button to start the Drain programme.
“Intensive Rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helping people
with allergies.
“Eco” button
• With a modified temperature profile and a slightly
prologned washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
PROGRAMME END
• The symbols of the programme sequence indicator
are dark, and the “Door open” indication lights up.
1. Turn the programme selector to the “On/Off” position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end.
• Press the “Reset” button for at least 3
seconds. Any existing water is drained out before the
lid can be opened.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
“Easy ironing” button
• Can be used together with “Cotton”, “Synthetics”
and “Daily load” programmes to make ironing easier.
• Increases the water quantity and the clothes are spun
very gently.
Rinse Hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
START DELAY
The “Start delay” allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper.
• Select programme, temperature, spin speed and
options.
• Press the “Start Delay” button to select the delay
time up to 23 hours.
• Press the “Start/Pause” button.
The countdown of the delay time begins; the clock
symbol next to the delay time and the dot between
hours and minutes flash.
• The time delay indication disappears when the
programme starts and it is replaced by the remaining
programme time.
• Once having pressed the “Start/Pause” button,
the number of hours preselected can be reduced by
pressing and holding the “Start delay” button. From
1 hour on, the delay time can also be reduced by
minutes.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Select another programme or press the “Drain/
Reset” button.
..after having pressed the “Start/Pause” button:
• Press the “Reset” button for at least 3
second - the start delay time dissapears from the
display.
SAVE YOUR FAVOURITE PROGRAMMES
If there is a programme setting which you use frequently,
the appliance offers the possibility to save one setting
for each programme so that it can be used again by just
pushing one button.
• Select the desired programme, temperature, spin
speed and option(s), push and hold the
“Favourites” button for at least 3 seconds.
The lamp next to “Favourites” shortly flashes and
then lights up - the programme settings is saved.
Next time you want to use your individual programme
settings, select the programme, push the “Favourites”
button and start by pushing “Sart/Pause”.
If you want to replace the saved programme
setting by another one:
• Push the programme button, select temperature,
spin speed and options as desired and then press and
hold the “Favourites” button for at least 3 seconds.
The previously saved programme setting will be
replaced by the new one.
LOCK BUTTON
You can lock the buttons of the control panel against
improper use (e.g. by children).
• Press the temperature and spin speed button
simultaneously and hold them for at least 3 seconds.
The key symbol on the display lights up.
• To unlock the buttons again: proceed in the same way.
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel (Reset) a running programme before
the end”.
