47629
12
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
10
GB
If despite all this your washer-dryer is still not running properly,
call your local Authorized Service Centre providing the
following information:
- fault
- model code (Mod. ....)
and serial number (S/N ....)
shown on the data plate at the back of your washer.
Never use the services of an unauthorised servicing technician
and insist on the use of original spare parts.
Installation
Transit packing
After removing the packing, check the appliance for damage.
If you have any doubts do not use the washer and call a qualified
technician. Keep the packaging components (plastic bags,
polyester foam, nails etc.) out of the reach of children since
they could be dangerous. The interior of the washer-dryer, has
an oscillating unit which is fixed on the back by 3 screws
during transport (figure 3). Before starting up the washer-dryer,
release the unit, by unscrewing the 3 screws. Seal the screw
holes with the plastic plugs supplied with the appliance.
Levelling
The washer-dryer must be perfectly levelled. To level the
appliance, only the front feet need to be adjusted
(see fig. 4); remember that the inclination of the working
surface must not be more than 2 degrees. If the washer-dryer
is installed on a carpeted floor, check that there is sufficient
ventilation space between the floor and the bottom of the
washer-dryer.
Water supply
Both hot and cold water supplies are preferable and they should
be between 34.5kN/m²(5lb/in²) and 1034.2kN/m² (150lb/in²)
pressure. The hose having the red end fitting should be en-
countered between the hot supply and the threaded connec-
tion adjacent to the letter H on the rear of the machine. The
hose having the white end fittings should be connected be-
tween the cold supply and the threaded connection adjacent
to the letter C on the rear of the machine (see fig. 5). Remem-
ber to insert a sealing washer at each connection to ensure
watertight joints. Do not overtighten the connections by
using tools -hand tight is sufficient to prevent leaks. It is gener-
ally more convenient to have these supplies away from the
sink taps. Where no suitable hot water supply is available or it
does not meet these requirements, both inlet hoses may be
connected to a cold supply by using two taps etc., or a «T»
junction on the plumbing (see fig. 6) however, use of cold
water only will increase programme times.
Note: the maximum temperature should not exceed 70°C
(158°F).
Drain hose
The drain hose (hooked pipe) is secured to the rear of the
machine by support clips and may be routed to right or left as
required (see fig. 7). The drain hose should be placed in a
stand pipe with a minimum internal diameter of 38 mm (1½
inches) or it can be positioned over a sink (see fig. 8) or it can
be connected as shown in fig. 9. The height of stand pipe or
sink should be between 60 and 100 cm (24 and 40 inches).
Care must be taken that the hose is not obstructed, twisted,
submerged or kinked. If the hose is connected with an airtight
joining, provision should be made to prevent syphoning.
Fig. 3
Fig. 4
Fig. 5
Fig. 6
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ariston AB1030C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ariston AB1030C in de taal/talen: Engels als bijlage per email.

De handleiding is 0,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info